PM110 Series Medically Approved

        110W
        Single to Quad Output

        Open Frame AC/DC Switchers 
 
 
 
      Data
        Sheet
 
 
 
 
 


        

          
EN 61000-3-2 Compliance
          
UL, CSA & TUV Approved
          
CE Marked
          
85 to 264 VAC Universal Input
          
4,000 VAC Isolation
          
Low Leakage Current
          
Meets Medical EMI Requirements
          
Overvoltage & Overcurrent Protections
          
Power Fail Detection (PFD)
          
100% Burn-In
          
High Reliability
        
 
 
Input Voltage.............85 to 264 VAC
Input Frequency...........47 to 63 Hz
Inrush Current............15A@115VAC, 30A@230VAC; @25°C cold start
Input Output Isolation....4,000 VAC
Leakage Current...........90µA max. @115VAC/60Hz, 150µA max. @230VAC/50Hz
Ripple & Noise............1% peak to peak max.
Overcurrent Protection....Short circuit protectin on all outputs
Overvoltage Protection....112% to 132% on main output
Power Fail Detect Signal..TTL logic high for normal operation,
                          TTL logic low upon loss of input power
Operating Temperature.....0-70°C; 100% load up to 50°C
Derating..................Derated 2.5%/°C from 50°C to 70°C
Hold-up Time..............12 msec min. at nominal input
Switching Frequency.......20K to 250K Hz, varies with load and line
Efficiency................65% min. at full load
Line Regulation...........±0.5% max. at full load
Safety Approvals..........UL2601-1, CSA C22.2 No. 601.1, TUV EN60601-1/IEC601-1
EMI Standards.............FCC Class B, EN55011 (CISPR 11) Level B
MTBF......................>400,000 hours at full load
Input Connector...........5-pin/3.96mm pitch, Molex 2878 compatible
Output Connector..........13-pin/3.96mm pitch, Molex 2878 compatible
Weight....................1.32 lb
Dimensions, W*L*H.........4.25*7*1.95 inches

Model No.	Output
	Vnom	Imin	Imax	*Ipk	*Pmax1	*Pmax2	Tol.
Single Output Models
PM110-10-1A	3.3V	0A	22A	---	52W	72W	±3%
PM110-10A	5V	0A	22A	---	80W	110W	±3%
PM110-12A	12V	0A	9A	---	80W	108W	±2%
PM110-13A	15V	0A	7.5A	---	80W	110W	±2%
PM110-14A	24V	0A	4.5A	---	80W	108W	±2%
PM110-16A	30V	0A	3.6A	---	80W	108W	±2%
Dual Output Models
PM110-23A	+5.1V  +12V	0A  0A	10A  5A	---  9A	80W	110W	±3%  ±3%
Triple Output Models
PM110-31A	+5.1V  +12V  -12V	0A  0A  0A	10A  5A  1A	---  9A  ---	80W	110W	±3%  ±3%  ±4%
PM110-32A	+5V  +15V  -15V	0A  0A  0A	10A  4A  1A	---  7.5A  ---	80W	110W	±3%  ±3%  ±4%
Quad Output Models
PM110-40A	+5.1V  +12V  -12V  -5V	0A  0A  0A  0A	10A  5A  1A  1A	---  9A  ---  ---	80W	110W	±3%  ±3%  ±4%  ±4%
PM110-41A	+5.1V  +15V  -15V  +24V	0A  0A  0A  0A	10A  4A  1A  1A	---  7.5A  ---  ---	80W	110W	±3%  ±3%  ±4%  ±4%
PM110-42A	+5.1V  +12V  -12V  +12V	0A  0A  0A  0A	10A  5A  1A  1A	---  9A  ---  ---	80W	110W	±3%  ±3%  ±4%  ±4%
PM110-45A	+5.1V  +12V  -12V  +24V	0A  0A  0A  0A	10A  5A  1A  1A	---  9A  ---  ---	80W	110W	±3%  ±3%  ±4%  ±4%
PM110-45-1A	+5.1V  +12V  -12V  +24V	2A  0A  0A  1.5A	10A  5A  1A  3A	--- 9A  ---  ---	80W	110W	±3%  ±3%  ±4%  ±10%
PM110-45-2A	+5.1V  +24V  -12V  +12V	0A  0A  0A  0A	10A  3A  1A  1A	---  5A  ---  ---	80W	110W	±3%  ±3%  ±4%  ±4%
PM110-46A	+5.1V  +15V  -15V  -5V	0A  0A  0A  0A	10A  4A  1A  1A	---  7.5A  ---  ---	80W	110W	±3%  ±3%  ±4%  ±4%
*Ipk is the peak output current with 10% max. duty cycle for less than 60 seconds.   Total peak power must not exceed 130 watts.  *Pmax1 is the maximum total output power at free air convection.  *Pmax2 is the maximum total output power at 25 CFM forced air.
Note: Add suffix "B" for L-bracket , "C" for enclosure.